PiFace Digital is designed to plug on to the GPIO of your Raspberry Pi, allowing you to sense and control the real world. With PiFace Digital you can detect the state of a switch, for example from a door sensor, a pressure pad or…

The new and improved ProtoCam kit for your Raspberry Pi A+/B+ and RPI B v2.

Comes as a DIY solder kit, no Pi nor Pi-Cam included.

Brought to you by: AverageManVSRaspberryPi

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux…

It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model A+,…

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USBSerial conversion chip and at the end of the 36" cable are four wire - red power, black…

WHAT IS THE PROTOCAM?The ProtoCam is a prototyping board for the Raspberry Pi Model A and B, that offers a whole new way to prototype with your Raspberry Pi. It's designed to hold your Raspberry Pi Camera Module - surrounded by…

The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy.

That's why we now carry the Adafruit Pi T-Cobbler Plus - Breakout + Cable for Raspberry Pi B+.
This…

The Raspbery Pi 26 Pin (2 x 13) GPIO Connector Header Extender with 90 Degree Angle can be used to raise the height of the GPIO pins on your Raspberry Pi. Each GPIO header will raise the height of the GPIO Pins by approximately…

TriBorg is a GPIO header replicator board for your Raspberry Pi. It converts the single GPIO header on the Raspberry Pi into three, and enables the addition of breakout boards, add-on boards or just about anything that's designed…

The PiCoolFan is an Advanced Cooling Fan System for the Raspberry Pi, that offers total temperature control and includes a Real Time Clock! The PiCoolFan is suitable for all Raspberry Pi users whose board reaches a high…

The PiRack is an expansion board allowing the connection of multiple IO boards to the Raspberry Pi. It also enables the Pi Camera Module to be used at the same time as expansion boards. Click here to see the Safety Leaflet.

Room…

Gertboard is een add-on voor de Raspberry Pi. De voorganger van de PiFace en voorzien van een eigen Arduino chip. Je combineerd dus de kracht van Pi met Arduino.

Dit extenderboard is niet geschikt voor mensen die net beginnen met…

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USBSerial conversion chip and at the end of the 36" cable are four wire - red power, black…

PiFace Digital is designed to plug on to the GPIO of your Raspberry Pi, allowing you to sense and control the real world. With PiFace Digital you can detect the state of a switch, for example from a door sensor, a pressure pad or…

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi T-Cobbler from Adafruit, which can break out all…

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi T-Cobbler from Adafruit, which can break out all…

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi Plate from Adafruit, which can snap onto the Pi…