• Stepper Motor Mount with Hardware - NEMA-17 Sized
    Stepper Motor Mount with Hardware - NEMA-17 Sized

    You have a stepper motor, but you need to attach it to your CNC project, eh? Not so easy if you don't have a stepper motor mount just like this fine one one here! This mount will fit any NEMA-17 motor (with 31mm hole spacing) with…

    € 9,95
  • Micro Servo - High Powered, High Torque Metal Gear
    Micro Servo - High Powered, High Torque Metal Gear

    Add even more power to your robot with this metal-geared servo. The tiny little servo can rotate approximately 180 degrees (~90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any…

    € 13,95
  • Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit
    Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit

    Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control.

    Raspberry…

    € 24,95
  • Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit
    Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit

    The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux…

    € 19,95
  • Vibrating Mini Motor Disc
    Vibrating Mini Motor Disc

    *BZZZZZZZZZZ* Feel that? That's your little buzzing motor, and for any haptic feedback project you'll want to pick up a few of them. These vibe motors are tiny discs, completely sealed up so they're easy to use and embed.

    Two…

    € 2,95
  • Adafruit DRV2605L Haptic Motor Controller
    Adafruit DRV2605L Haptic Motor Controller

    The DRV2605 from TI is a fancy little motor driver. Rather than controlling a stepper motor or DC motor, its designed specifically for controlling haptic motors - buzzers and vibration motors. Normally one would just turn those…

    € 8,95
  • Small Reduction Stepper Motor - 5VDC 32-Step 1/16 Gearing
    Small Reduction Stepper Motor - 5VDC 32-Step 1/16 Gearing

    DESCRIPTIONThis is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with two mounting holes. There are only 32 step (11.25 degree) per…

    € 4,95
  • Stepper motor - NEMA-17 size - 200 steps/rev, 12V 350mA
    Stepper motor - NEMA-17 size - 200 steps/rev, 12V 350mA

    DESCRIPTIONA stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor was specified to have a max current of 350mA so that it could be…

    € 15,95
  • Mini Pan-Tilt Kit - Assembled with Micro Servos
    Mini Pan-Tilt Kit - Assembled with Micro Servos

    DESCRIPTIONThis fully-assembled pan-tilt kit is the perfect way to give your project full range motion with two micro servos. The pan-tilt can rotate roughly 180° from side-to-side and can tilt up&downwards around 150°. It also…

    € 21,45
  • DC Motor
    DC Motor

    DESCRIPTIONThese are standard '130 size' DC hobby motors. They come with a wider operating range than most toy motors: from 4.5 to 9VDC instead of 1.5-4.5V. This range makes them perfect for controlling with an Adafruit Motor…

    € 2,50
  • ULN2803A: 8 Channel Darlington IC - Solenoid, DC & Stepper Motor Driver
    ULN2803A: 8 Channel Darlington IC - Solenoid, DC & Stepper Motor Driver

    Bring in some muscle to your output pins with 8 mighty Darlingtons! This DIP chip contains 8 drivers that can sink 500mA from a 50V supply and has kickback diodes included inside for driving coils. This will let your little…

    € 2,95
  • L293DNE: Dual H-Bridge IC - Solenoid, DC & Stepper Motor Driver
    L293DNE: Dual H-Bridge IC - Solenoid, DC & Stepper Motor Driver

    The L293DNE Dual H-Bridge IC is able to run four solenoids, two DC motors or one bi-polar or uni-polar stepper motor, with up to 600mA per channel!

    Each chip contains two full H-bridges (four half H-bridges) which means you can…

    € 2,95
  • PCA9685 16 Channel 12-bit I2C PWM/Servo driver
    PCA9685 16 Channel 12-bit I2C PWM/Servo driver

    You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a…

    € 14,95

 

 Our collection of robotica products.
 We are happy to have these wonderfull products in store.

Click the following link to view our Makeblock collection:  

 

© 2013 - 2024 V.O.C.-Electronics | sitemap | rss | ecommerce software - powered by MyOnlineStore